آلة تعبئة يدوية

A manual liquid filling machine is a hand-operated dispensing device: the operator pulls a lever or pushes a handle to draw liquid from a supply tank into a piston cylinder, then dispenses it into a container. No electricity, no compressed air, no PLC. It is the simplest and most affordable filling equipment available. Typical users: micro-businesses and artisan producers (home kitchen, garage, market stall); laboratory and R&D sampling (1–10ml dispensing with precision syringe-style fillers); remote locations with no reliable power supply; event or field filling (water, fuel, chemical sampling); and businesses filling very expensive products where any waste is costly and batch sizes are tiny (1–50 units/day). Manual fillers are not suitable for production above ~500 units/day.

Manual piston fillers achieve ±2%–±5% accuracy in typical operation. For example, a 200ml fill will be 190ml–210ml depending on operator consistency and liquid temperature. Accuracy is affected by: operator technique (pull speed and force); liquid viscosity and temperature; nozzle wear; and back-pressure from narrow-neck containers. For better accuracy with manual equipment, a manual net-weight scale filler (operator fills until the scale reads target weight) achieves ±0.5%–±1%. For products requiring tighter fill tolerances, a semi-automatic piston filler (±1%) or automatic servo filler (±0.3%) is recommended. Manual fillers are generally suitable for products where ±2%–±5% fill variation is acceptable, such as personal care products, industrial chemicals and food ingredients sold by declared volume with generous tolerances.

Manual gravity piston fillers handle: water-thin liquids (water, juice, vinegar, alcohol, essential oils — <100 cP) best; medium-viscosity liquids (thin sauce, syrup, shampoo — 100–3,000 cP) at reduced speed; and mildly viscous liquids (thicker lotion, honey at room temperature — 3,000–15,000 cP) with effort and reduced accuracy. Manual fillers cannot reliably handle very thick products (peanut butter, petroleum jelly, heavy adhesive — >15,000 cP) because the operator cannot generate enough pressure for consistent fills. For very thick products at small scale, a manual gear pump with hand crank is available. Corrosive liquids (acid, alkali, solvent) require manual fillers with PVDF or PTFE wetted parts instead of SUS304/316L.

Manual piston filler: operator pulls a lever to draw a measured volume of liquid into a piston cylinder, then pushes to dispense. Volume is controlled mechanically. Works with thin to medium viscosity liquids. Gravity filler: liquid flows from an elevated tank through a valve into a container purely by gravity. No piston, no pump. Volume controlled by time (timed gravity) or float valve (level gravity). Suitable only for thin, free-flowing liquids (water, juice, alcohol). Gravity fillers have no ability to fill thick or viscous liquids. Manual piston fillers are more versatile and accurate than gravity fillers. Gravity fillers are even cheaper and simpler but only work for thin liquids at low speeds.

Upgrade triggers: production volume exceeds 200–500 units/day consistently; fill accuracy complaints or product loss from over-filling becomes significant; operator fatigue is causing quality variation; labour cost of manual filling exceeds the amortised cost of a semi-automatic filler; you are scaling to retail or e-commerce channels that require consistent fill declarations on labels; regulatory requirements (GMP, FDA) require documented fill records that manual filling cannot provide. A semi-automatic filler ($1,500–$6,000) pays back in labour savings within 6–18 months at 300–1,000 units/day. An automatic filler ($15,000–$50,000) is justified at 1,000–5,000+ units/day.

Manual lever piston filler (50ml–500ml, SUS304): $500–$1,200 USD. Manual piston filler with wide fill range (10ml–1,000ml): $800–$2,000 USD. Manual gear pump filler with hand crank (50ml–5,000ml, for viscous): $1,000–$2,500 USD. Manual syringe dispenser (1ml–100ml, lab/pharma grade): $300–$800 USD. All models include CE certification and SUS304/316L product-contact parts. Prices include one nozzle set and basic spare parts kit. Contact us for bulk pricing or custom configurations.